Product Range ▼ Paving Breaker CP 0112
 
OPERATING AIR PRESSURE : Air pressure should be between 87 psi, 6 bar at the tool during operation. Use at higher pressures will increase recoil to the operator, decrease performance and output, and may cause damage to tool. Lower pressure will also reduce tool performance. It is important to realize that the use of long lead hoses, manifolds and worn hose connections in the air line leading upto the tool will cause a pressure drop. Use couplings and fittings of maximum inner diameter for the size of hose being used (Refer to the specifications chart for this data). Reducers will restrict the air and therefore result in less pressure at the tool.

COMPRESSED AIR SUPPLY : Use an air compressor with sufficient CFM (Cubic Feet per Minute) delivery to operate the tool(s) at a pressure of between 87 psi, 6 bar. Refer to the specification chart for CFM requirements.

AIR HOSE CONNECTION : Inspect air hoses, fittings and gaskets for cuts, abrasions and wear. Check that fittings, both in the tool and on the hose, are secure. Use safety wire or chain to secure the couplings at the tool to prevent hose whipping, should the hose become detached while pressurized. Clear hoses of debris and excess water before attaching them to the tool. For hoses in excess of 1/2" inside diameter install a proper flow limiting valve per OSHA standards.

RECOMMENDED LUBRICATION PROCEDURE : The CP 0112 range of Utility Hammers require minimal lubrication under normal operating conditions. Oil carryover from the compressor, combined with moisture in the air, will not normally suffice to provide sufficient lubrication to this series of tools. The use of an external line lubricator in the air line between the compressed air source and the tool is recommended. Use KSC-0.5 line oiler for this application. A slight mist of moisture/oil should be present at the tool exhaust and on the shank of the steel. This is a
sign of adequate tool lubrication. A drill rod coupling lubricant should be applied to the shank of the steel. Please refer to the table on Lubrication for recommended lubricants.
 

 

Features
»
Forged, heat treated, all alloy steel construction.
»
Integral oil chamber in backhead.
»
Honed Cylinders, lapped leakproof mating surfaces.
»
Gooseneck air swivel for easy handling and positioning.
»
Muffler available as on option.

 

Application :- Asphalt cutting, demolition of reinforced concrete, rock outcrop and pavement.

Model CP 0112
Weight with silencer 14.5 kg 32 lb
Weight without silencer 13.5 kg 30 lb
Length 535 mm 21"
Air pressure 6 bar 87 psi
Air consumption 23 l/s 49 cfm
Blows per minute 1620
Air inlet 19 mm 3/4"
Shank size (standard) - 8900 0030 25, 8900 0030 23 25 x 108 mm 1" x 4¼”
Retainer type Latch




PART LIST PAVING BREAKER CP 0112

No. Description
Lever - Throttle valve
Remark Quantity Part number
R070110
2 Handle - Rubber   2 R005716
3 Plug - Oil   1 R000560
4 Pin - Trigger     R133433
5 Nipple - Air linlet     R075227
6(7-9) Backhead, complete     R070105
7 Backhead      
8 Bushing - Throttle valve     R070106
9 Bushing - Throttle valve stem     R070109
10(11-14) Valve - Throttle, complete     R045370
11 Valve - Throttle      
12 Seal - Valve      
13 Retainer - Seal      
14 Spring - Throtue valve      
15 Plug • Throtue valve bushing     R070108
16 Valve     R070103
17 Block - Valve     3303 0051 :
18 Piston     R070102
19 Cylinder      
20 Bushing     R070112
21 Nut - Backhead bolt Y,c" -18 4 P006099
22 Bolt - Backhead Y,c" -18 4 R070111
23(24 -34) Latch retainer, complete     R092500
24 Head - Latch retainer      
25 Nut - Head latch Y." -13   R000555
26 Lockwasher - Head latch     C036717
27 Bolt - Head latch Y." -13 x 2'\r."   P002123
28 Bolt - Latch retainer o/." -18 x 3'h"   R092498
29 Bushing - Latch retainer bolt     R092499
30 Nut - Latch retainer %" -18   P081091
31 Spring - Latch retainer plunger     R086982
32 f'lunger - Latch retainer     R092497
33 Bushing - Latch retainer     R048540
34 Retainer - Latch     R092493
 
 
 
 
Corporate Information Contact Information   STAY CONNECTED
»
Company Profile
»
Quality Assurance
»
Infrastructure
»
Contact Us
82, Industrial Area-A,
Ludhiana141003, Punjab India
+919855565923
+919878603423
+911614646016
saleskscgroup@gmail.com
www.kscgroup.in
 
Copy © 2020-21 KSC Metallurgy Pvt. Ltd. All Right Reserved
Powered By : Ayushi Online